Two Car rustic shingle wall exterior capped with sleek metal roofing detached garage with workshop is a compliment to any building site location. The garage workshop portion of this open floor plan boasts the added convenience of a full bath. Add a partition wall to separate the garage from the workshop for additional comfort or increased security. The unfinished second level storage area with vaulted ceilings is intentionally left undeveloped to allow your personalization of this space.
|Bonus Area:||736 sq ft|
|Garage Area:||864 sq ft|
|Number of Stories:||2|
|Max Ridge Height:||24'2 from Front Door Floor Level|
|Primary Roof Pitch:||12:12|
|Roof Load:||32 psf|
|Main Ceiling Height:||9'|
|Upper Ceiling Height:||10'|
We are sorry, but an estimated cost build is not available for this particular plan.
A: I calculate the approximate mid gable height to be 16’-6”. (measured to the mid height between the loft floor to the top of the ridge beam) An option, going to an eight foot first level from nine feet and a slight roof pitch reduction, would get the height to your allowable fifteen feet. Thank you for your interest in one of my designs,
A: Sorry the only roof design that is pre-drawn is the one shown on the web site. The living space size would be dictated by the Gambrel framing type, either conventional framed of roof trussed. You may lose some living space width but you would gain with more usable wall height. The benefit with using gambrel roof trusses, is that it would eliminate the need for the support posts in the garage area. Thank you for your interest in one of my designs. Regan
A: Sorry. The answer that you are referring to, is an answer that was for my design number 76016 and was posted here by mistake. Design 76019 is a manual drawing and not available in a cad format. You can purchase a PDF of this design if you can work with that format. Best regards, Regan
A: You could use engineered attic trusses which would span the entire width of the garage and eliminate the need for the support posts in the garage and the loft area. The attic trusses are designed for this type of situation. Thank you for your interest in one of my designs.
A: Based on the publication “The Span Book” from the Canadian Wood Council: For roof joists, roof snow load of 52.2 psf: 2 x 10 no. 2 D. fir- larch would span 12’-7” at 24” o.c. 0r 2 x 10 no. 2 hem-fir would span 13’-2” at 24” o.c. Or 2 x 10 no. 2 spf would span 12’-6” at 24” o.c. So either one of these species would still work at 24” o.c. for this design. Best regards, Regan
A: The composite live load for design 1741 is 32 psf which is the equivalent to a ground snow load of 44 psf. If your ground snow load is 84 psf you would need to enlist the services of a engineer registered in the state where the construction will occur to provide a snow load upgrade. The design calls up conventional roof framing with 2 x 12 roof joists at 24 inches on center. You can purchase a pdf or CAD file of this design from familyhomeplans to simplify this upgrade process. Please email with any questions or if you require any additional information. Best regards, Regan
A: Hi, Presently the garage and workshop area are open to each other. It would be easy to add a wall from the end of the workshop across to the entry man door. This wall would just be a non-loading bearing partition wall, and not supporting any structure. Best regards, Regan
A: The garage has a nine foot ceiling height with two nine foot wide by eight foot high garage doors.
I would be happy to modify this garage to suit your specific requirements, if required.
A: Yes to converting the garage workshop into a kitchen area. The inside dimensions for this space is 10’-4” wide by 11’-6” deep. If this garage loft is intended to sleep in, and the garage is to have vehicles, you would need to close off between the garage and the living space. Presently the loft is open to the garage.
The loft slopes from 2” at the exterior wall to 10’ at the interior peak. The middle portion measured at 6’-6” high would have a width of 10’-4”.
Please email with questions or if you require any additional information.
Thank you for your interest in one of my designs,
A: The overall height for design is 24’-2”, from the finished grade to the ridge.
A: Yes you can! Please click the "Modifications" tab above to get more information.
A: The national average for a house is running right at $125.00 per SF. You can get more detailed information by clicking the Cost-To-Build tab above. Sorry, but we cannot give cost estimates for garage, multifamily or project plans.
Have any Questions? Please Call 800-482-0464 and our Sales Staff will be able to answer most questions and take your order over the phone. If you prefer to order online click the button below.Add to cart